LDE P Series

genset for island operation, standby and parallel operation with the network and / or other genset. standard equipment of the generating sets: engine cooling system, starter, alternator and exhaust silencer, alternator with automatic voltage regulator (avr), baseframe with fuel tank and the collecting vessel, basic wiring, batteries, coolant and lubricating oil.

Perkins Engines

diesel engines, 4-stroke, direct injection, charging through the turbine and / or intercooled, suitable for continuous operation or standby operation.
perkins engines provide economical power in operation. another advantage, which has been planned in the development of  engines is reliability. engines provide low lubricating oil consumption and low wear. extremely compact dimensions and the relationship between power and weight allow smaller dimensions of the generating sets and cost-effective transportation. engines are designed to allow easy maintenance and servicing. ensuring low exhaust emissions during operation have a minimal impact on the environment. minimum fuel consumption maximizes engine performance.

Alternators

the alternators are synchronous, three-phase, brushless, self-regulated, self-excited, self-ventilated and 4 pole. insulation class h (temperature rise according to class f or b on request). tropical impregnation for salty-humid environment is possible on request. automatic voltage regulation. protection class ip21 or ip23 (other class on request).

Base Frame

steel construction - monobloc. anti-vibration mounting to eliminate the vibration. powder coated with primer and  cover color. the base frame is designed to enable simple lifting and moving the generating set.

Fuel Tank

the fuel tank is mounted on the inside of the base frame. under the fuel tank, a collecting vessel is mounted, which prevents outpouring of any liquid from the generating set into the environment. equiped with all necessary connectors and sensors. standard autonomy of the tank is 8-10 hours at 75% load. additional freestanding double wall tanks and automation for pumping fuel on demand.

Control Panels

manual – includes a manual control unit (push button / key start type), main circuit breaker, differential protection and all auxiliary controls and alarms.

automatic – includes an automatic control unit that starts the genset in case of mains failure (it can be started manually too), main circuit breaker, differential protection and all auxiliary controls and alarms, button for emergency stop, changeover genset / mains (ats) on request.

synchronization – automatic control cabinet for synchronization more generating sets and / or main electricity network and parallel operation. additional and special control and switching cabinets for genset on demand.

Standard housing

Standard sound insulated housing, suitable for outdoor and indoor application. It is equipped with four doors with locks for easy maintenance and servicing of the genset. Fixed louvers at the entrance and exit for engine cooling, exterior or interior point for fi lling the fuel tank. All housings are powder coated with primer and cover color (standard color RAL 7035, other colors on request). Standard noise level is 72 ± 3 dB at a distance of 7 m (lower noise levels on request). Possibility of special
housing on request.

Image: Standard housing

Container housing

Container housing for bigger genset, low noise levels and the specific working conditions of generating sets. Container housing standard lengths of 20‘ (6 m) and 40’ (12 m). Fixed louvers at the entrance and exit for engine cooling, exterior or interior point for fi lling the fuel tank. Container housings are painted with primer and cover color. Suitable for outdoor and indoor installation. Possibility of special container housing on request.

Image: Container housings

Noise absorber

For noise reduction we can mount silencer in the housing and / or in the air duct. Silencers are made of fi reproof materials. According to the needs of the noise level our engineers calculate and adjust the size and number of dampers for the genset.

Transport trailer

Trailers for non-road transport

Trailers, ready for non-road transport. Transport on construction sites, industrial zones ... One or two axle version, the tandem version. Transport speed max. 40 km / h.

Trailers for road transport

Certified and approved trailers for road transport. Singleaxle, twin-axle, tandem trailer. BPW / SAF-axle, air suspension, towing eye, spare wheel holder with a spare wheel, electric installation according to standards EG, ABS brakes, side lateral protection, height-adjustable towing ore, common earth point and all the equipment necessary under road traffic regulations.

Image: Generating set on two-axled trailer

Image: Generating set on one-axled trailer

Equipment

• Lifting arc with lifting eyes,
• corner castings on the container housings,
• equipment for operation in harsh ambient conditions(high dustiness, high relative humidity, low / high ambient temperature ...),
• power cables retractors,
• emergency stop key on the housing.

Image: Various control cabinet according to the user's needs

Manual cotrol cabinet KO-R MRS

Manual control cabinet can be mounted on genset or delivered separately. It includes the entire control and management of the engine and generator, and remote start of the genset. By pressing a button (key) genset starts and stops (also from a remote location). Genset can also start and stop by signals to be obtained from the outside (remote start).

It consists of a metal electrical cabinet, manual control panel of the genset SMC10, the generator protection circuit breaker, emergency stop key and fuses. The cabinet is ready to connect the power cable for consumers on a copper strip or staples.

Image: Manual controller Stubelj Nano 5 and Stubelj SMC 10 NT

Automatic control cabinet KO-A AMF

Automatic control cabinet can be mounted on genset or delivered separately. It includes the entire control and management of the engine and generator, and remote start of the genset. It allows the automatic start of the genset at main power network failure and stop on its return. Automatic control cabinet can operate in the following modes: AUTO / MANUAL / TEST / OFF. Genset management is provided by the keys with mechanical feedback and a large graphic display. Management and control can be run also through remote computer (PC). It is possible to connect generating sets in the network.

It consists of a metal electrical cabinet, automatic control panell of the genset SAC35, the generator safety switch, emergency stop key and fuses. The cabinet is ready to connect the cable of the consumers on a copper strip or staples.

Image: Automatic controller Stubelj Nano 5 and Stubelj SAC 35 NT

Paralel synchonization control cabinet KO-P AMF

Automatic sync control cabinet can be mounted on genset or separately. It includes the entire control and management of the engine and generator, and remote start of the genset. It enables the automatic start of the genset when main power network fails and stops on its return. It also enables synchronization of network and genset and parallel operation of the genset and main electric network. The parallel synchronization control cabinet can also cover electrical spikes. In  case that the designated facility needs additional electricity, genset in parallel operation can add this deficit to the main electrical grid. Genset can also cover a specific part of the power so that is no need  to be collected from the main electricity network and pay credits at a higher rate.  Genset performs uninterrupted switching between the network and genset. It is also possible for uninterrupted test of the genset at full or partial load. Genset management is possible by keys with mechanical feedback and a large graphical display. Management and control can be run also through remote computer (PC). It is possible to connect generating sets in the network.

It consists of a metal electrical cabinet, parallel control panel of the genset Stubelj SPC50, the generator safety switch, battery charger emergency stop key and fuses. The cabinet is ready to connect the cable to consumers on a copper strip or staples.

Extensions:

• 4 analog inputs 0-2400 Ω, 8 digital inputs, 8 binary outputs, 1 analogue output,
• 4 analog inputs Ω/0-20 mA/0-100 0-250 mV, 8 digital inputs, 8 binary outputs, 1 analogue output,
• 15 green / yellow / red LED indicators.

Communication Extensions:

• Ethernet / Internet communication supports control of multiple generating sets over the Internet, an active e-mail on error on genset, internet function call / callback.
• Direct or modem control of multiple generating sets RS232 / RS485 / ModeBus support for direct connection, analog / GSM / ISDN modem support, call-back feature on your modem.
• Software for PC or PC SCADA.
• Software for PC for long-term monitoring of events multiple generating sets.
• Controller software for automatic acquisition of data on multiple genset via modem.
• Remote display connected via RS232, to transfer all of the displayed values ​​to 1.2 km away - the exact copy of the OSD control.

Image: Controller Stubelj SPC 50

Upgrading

ATS automatic transfer switch genset / mains

Control power (for one genset in parallel with the network):

• automatic synchronization and control of power,
• cutting peaks,
• uninterrupted reverse synchronization,
• voltage control PF (AVR),
• basic load export / import.

Load sharing (for more isolated parallel operation):

• automatic synchronization and control of power,
• voltage and PF control (AVR),
• active load sharing.

Load sharing and power management (for more isolated parallel operation or more motors parallel with the network):

• automatic synchronization and control of power,
• voltage control PF (AVR),
• active load sharing,
• the sharing of Var (via CAN bus).

Optimizing the number of operating generating sets:

• power management (via CAN bus) in kW or % of the power,
• monitoring and control of multiple generating sets via MultiEdit.